The growth of the flock requires ample water and is well known to farmers. Therefore, it is especially important to add enough water to the laying hens. If the water shortage of the laying hens will not only affect the laying of the laying hens, but also seriously affect their metabolism. Therefore, farmers need to control the drinking water and drinking time of the laying hen scientifically and reasonably in Poultry Farming Machinery price for kenya.

1. The drinking time of laying hens

The flock will have 3 drinking water peaks every day, that is, every morning at 8:00, 12 noon, and around 6 pm. The drinking time of chickens is mostly in the light time. At around 8 in the morning, the chicken began to receive light; around 12 noon, it was the peak time for laying eggs. After the hen had finished producing the eggs, the body consumed more water and felt very thirsty to drink water; around 6 pm, the light The time is coming to an end, ready to enter the evening to start the rest, the chicken should drink enough water to facilitate the spare time in the evening. If the laying hens do not drink water or drink less water during the peak period of the three water needs, the egg production of the chickens will decrease, and their health will also be manifested.

2. The amount of water in the laying hen

Under normal circumstances, the daily drinking water required for each laying hen is about 110 ml in winter, about 280 ml in summer, and about 200 ml in spring and autumn. When the laying rate of laying hens increases, the amount of water they drink will also increase. Because at this time the laying hens have strong egg production and enhanced metabolism, not only do they need to form water for the eggs, but as the feed intake of the flock increases, the amount of water required will gradually increase. Therefore, pay special attention to the water supply work of the chickens during the peak laying period of the laying hens, otherwise it will directly affect the health and egg production of the laying hens in Chicken Breeding Equipment Machinery.

Like some large-scale farms, the cleaning work of the farmers will be done using a automatic manure removing machine. Therefore, the normal use of the septic machine and the service life are very important, which requires the farmers to maintain and maintain them regularly during normal use, so as to maintain their performance and extend the service life. So how do we carry out the maintenance of the cleaning machine?

1. When the septic belt runs 10cm away from the edge of the passive roller at the head end, it can be adjusted by tightening the bolt on the tension rod. When the septic belt moves back one-third of the time, the bolts should be properly loosened to prevent the septic belt from being carried back over the head;

2. When the clearing belt runs close to the edge of the passive roller, the tension chain can be released, the cleaning belt is moved by hand to the middle of the passive roller, and then the tension chain is mounted on the sprocket, and then tightened with a pipe wrench. The hexagonal shaft can be tightened until the bolt is tightened;

3. It is necessary to pay attention to the maintenance of the conveyor belt cleaning machine. After the cleaning belt is used for a period of time, the phenomenon of prolonging the loosening will occur. It is necessary to cut off a section and re-weld. Be sure to buy an ultrasonic plastic welder. When welding, the two ends should be aligned and cannot be skewed;

4. If the automatic cleaning machine has a tape winding situation, just remove the manure in the passive roller and unfold it, and adjust the main body tensioning wire. Never cut;

5. Regularly inspect the bearings and rubber rollers every month. The bearings should be greased regularly. The rubber rollers should be kept tight and not loose.

6. The maintenance of the horizontal automatic cleaning machine is the same as that of the loading conveyor, which is relatively simple;

7. The tail end deviation is relatively rare, the main reason is that the rubber roller is not pressed tightly. If the deviation is reversed, the farmer can adjust by adjusting the tightness of the outermost bolt, and then press the rubber roller. If the tape is reeled, the rubber roller is pressed after adjusting the bolt, and then a stick is used to spread the flat strip of the front roller of the large roller during operation, and the tape winding problem is naturally solved when the operation is performed.

The above is the author's introduction, the basic method of maintenance of the manure machine when using automatic poultry farming equipment, want to know more information, welcome to continue to pay attention to our website.